Description
| Range of Product | Altivar 32. |
|---|---|
| Product or Component Type | Variable-speed drive. |
| Product destination | Asynchronous motors. Synchronous motors. |
| Product-Specific Application | Complex machines. |
| Function Available | – |
| Assembly style | With heat sink. |
| component name | ATV32. |
| EMC filter | Class C2 EMC filter integrated. |
| Phase | 1 phase |
| [Us] rated supply voltage | 200…240 V, 15…10 %. |
| Supply voltage limits | 170…264 V. |
| Supply frequency | 50…60 Hz, 5…5 %. |
| Network Frequency | 47.5…63 Hz. |
| Motor power (kW) | 0.18 kW 200–240 V. |
| Maximum Horse Power Rating | 0.25 hp 200…240 V. |
| Line current | 2.8 A 240 V, 1 phase, 0.18 kW, / 0.25 hp. 3.4 A, 200 V, 1 phase, 0.18 kW, 0.25 hp. |
|---|---|
| Apparent power | 0.7 kVA 240 V, 1 phase, 0.18 kW, / 0.25 hp. |
| Prospective line Isc | 1 kA, 1 phase. |
| Nominal output current | 1.5 A 4 kHz, 240 V, 0.18 kW, 0.25 hp. |
| Maximum transient current | 2.3 A 60 s, 0.18 kW, 0.25 hp. |
| Output frequency | 0.0005…0.599 kHz. |
| Nominal switching frequency | 4 kHz. |
| Switching frequency | 2…16 kHz adjustable. |
| Speed range | 1…100 asynchronous motor in open-loop mode. |
| Speed accuracy | +/- 10 % of nominal slip 0.2 Tn to Tn. |
| Torque accuracy | +/- 15 %. |
| Transient overtorque | 170…200 %. |
| Braking torque | <= 170 % with braking resistor. |
| Asynchronous motor control profile | Voltage/frequency ratio, 5 points. Voltage/frequency ratio: energy Energy Saving, quadratic U/f. Voltage/frequency ratio, 2 points. Flux vector control without sensor, standard. Flux vector control without sensors: energy Energy. Saving, no-load law |
| Synchronous motor control profile | Vector control without sensor. |
| Regulation loop | Adjustable PID regulator. |
| Motor slip compensation | Automatic, whatever the load. Adjustable 0…300 %. Not available in voltage/frequency ratio (2 or 5 points). |
| Local signalling | 1 LED red drive voltage. 1 LED green CANopen run. 1 LED red CANopen error. 1 LED red drive fault |
| Output voltage | <= power supply voltage. |
| Noise level | 43 dB 86/188/EEC. |
| insulation | Electrical between power and control. |
| Electrical connection | Screw terminal 0.5…1.5 mm2, AWG 18…AWG 14 control). (Removable screw terminals 1.5–2.5 mm2, AWG 14–.AWG 12 motor/braking resistor). Screw terminal 1.5–4 mm2, AWG 14–AWG 10 power supply). |
| Tightening torque | 4.43 lbf.in. (0.5 N.m.), 4.4 lb/ft. control). 6.20 lbf.in. (0.7 N.m.), 7.1 lb/ft. motor/braking resistor). 5.31 lbf.in. (0.6 N.m.), 5.3 lb/ft. power supply) |
| Supply | Internal supply for reference potentiometer (1 to 10 kOhm). 10.5 V DC +/- 5 %, <10 mA overload and short-circuit protection. |
| analogue input number | 3 |
| Analogue input type | AI1 voltage 0…10 V DC 30000 Ohm 10 bits. AI2 bipolar differential voltage +/- 10 V DC 30000 Ohm 10 bits. AI3 current: 0…20 mA (or 4-20 mA, x-20 mA, 20-x mA or other patterns by configuration) 250 Ohm 10 bits. |
| Sampling duration | 2 ms (AI1, AI2, AI3): analog. 2 ms (AO1): analog. |
| Response time | LI1…LI6 8 ms +/- 0.7 ms logic. R1A, R1B, and R1C 2 ms relay. R2A, R2C, 2 ms relay. |
| Accuracy | +/- 0.2 % AI1, AI2, AI3 for a temperature of -10.60 °C. +/- 0.5 % AI1, AI2, AI3 for a temperature of 25 °C. +/- 1 % AO1) for a temperature of 25 °C. +/- 2 % AO1) for a temperature of -10.60 °C. |
| Linearity error | +/- 0.2… 0.5%% of maximum value (AI1, AI2, AI3) +/- 0.3 % AO1). |
| analogue output number | 1 |
| Analogue output type | AO1 software-configurable current 0…20 mA, 800 Ohm, 10 bits. AO1 software-configurable voltage: 0…10 V, 470 Ohm, 10 bits. |
| Discrete output number | 3 |
| Discrete output type | Configurable relay logic (R1A, R1B, R1C): NO/NC: 100000 cycles. Configurable relay logic (R2A, R2B): NO: 100000 cycles Logic LO). |
| Minimum switching current | 5 mA, 24 V DC, configurable relay logic. |
| Maximum switching current | R1 3 A 250 V AC resistive, cos phi = 1. R1 4 A 30 V DC resistive, cos phi = 1. R1, R2 2 A 250 V AC inductive, cos phi = 0.4. R1, R2, 2 A, 30 V DC inductive, cos phi = 0.4. R2 5 A 250 V AC resistive, cos phi = 1. R2 5 A 30 V DC resistive, cos phi = 1. |
| Discrete input number | 7 |
| Discrete input type | Programmable (sink/source) LI1… LI4… 24… 30 V DC level 1 PLC. Programmable as pulse input 20 kpps LI5) 24…30 V DC level 1 PLC. Switch-configurable PTC probe LI6) 24…30 V DC. Safe torque off STO: 24.30 V DC, 1500 Ohm. |
| Discrete input logic | Negative logic (sink) LI1… LI6), > 19 V, < 13 V. Positive logic (source): LI1… LI6,, < 5 V, > 11 V. |
| Acceleration and deceleration ramps | S Deceleration ramp automatic stop DC injection. Ramp switching. Linear Deceleration and ramp adaptation. CUS U |
| Braking to standstill | By DC injection |
| Protection type | Input phase breaks drive. Overcurrent between output phases and earth drive. Overheating protection drive. Short-circuit between motor phases drive. Thermal protection drive. |
| communication port protocol | Modbus. CANopen.. |
| Connector type | 1 RJ45 on front face)Modbus/CANopen. |
| Physical interface | 2-wire RS 485 Modbus. |
| Transmission frame | RTU Modbus. |
| Types of polarization | No impedance Modbus. |
| Number of addresses | 1…127 CANopen. 1…247 Modbus. |
| Method of access | Slave CANopen |
| Electromagnetic compatibility | 1.2/50 µs–8/20 µs surge immunity test, level 3 IEC 61000-4-5. Conducted radio-frequency immunity test, level 3 (IEC 61000-4-6).. Electrical fast transient/burst immunity test, level 4 IEC 61000-4-4. Electrostatic discharge immunity test, level 3, IEC 61000-4-2. Radiated radio-frequency electromagnetic field immunity test, level 3 (IEC 61000-4-3). Voltage dips and interruptions immunity test (IEC 61000-4-11). |
| Width | 1.77 in. (45 mm). |
| Height | 12.80 in (325 mm). |
| Depth | 9.65 in (245 mm). |
| Net Weight | 5.29 lb (US) (2.4 kg). |
| Option card | Communication card: CANopen daisy chain. Communication card CANopen open style. Communication card: DeviceNet. Communication card: EtherNet/IP. Communication card Profibus DP V1. |
| Standards | EN/IEC 61800-3. EN 61800-3 environments 2 category C2. EN/IEC 61800-5-1. EN 61800-3 Environments, Category C2.. EN 55011, class A, group 1 |
|---|---|
| Product Certifications | C-tick CSA UL GOST NOM 117 |
| Marking | CE |
| Pollution degree | 2 EN/IEC 61800-5-1. |
| IP degree of protection | IP20 EN/IEC 61800-5-1. |
| Vibration resistance | 1 gn (13…200 Hz) EN/IEC 60068-2-6. 1.5 mm peak to peak (3…13 Hz) EN/IEC 60068-2-6. |
| Shock resistance | 15 gn 11 msEN/IEC 60068-2-27.. |
| Relative humidity | 5…95 % without condensation IEC 60068-2-3. 5… 95%% without dripping water IEC 60068-2-3. |
| Ambient air temperature for operation | 14…122 °F (-10…50 °C) without derating. 122…140 °F (50…60 °C) with derating factor. |
| Ambient Air Temperature for Storage | -13…158 °F (-25…70 °C). |
| Operating altitude | <= 3280.84 ft (1000 m) without derating. 3280.84…6561.68 ft (1000…2000 m) with current. derating 1 % per 100 m. |
| Operating position | Vertical +/- 10 degrees. |
| Category | 22000-Temporary Category for ITS Price Promotion. |
|---|---|
| Discount Schedule | I |
| GTIN | 00785901632160. |
| Returnability | No |
| Country of origin | ID |
